How to choose a snowboard vinyl wrap
Start with a film made to stick to your board’s top surface. Then check how it holds up in the cold and how it comes off. Measure your board before you pick a sheet size.
Check what the wrap needs to stick to
The snowboard topsheet, also written top sheet, is the exposed upper layer of the board. A vinyl film that covers this surface is called a topsheet wrap, or top sheet wrap. Before you choose a film, check whether your board’s surface feels smooth or has a raised texture. If you can, find the material and finish in the board maker’s notes. A photo may show the finish, but you can feel the texture better in person.
Give the seller your board’s brand, model and year. Ask if the glue works on that surface. If the seller offers a sample, ask how to test it and take it off. Check chips or loose spots on the topsheet before you cover them. Ask a board shop to look at any area that may need repair.
Board makers can use different materials and finishes. You can see examples in Isosport’s topsheet guide (PDF).
Compare the film, glue and top coat
- Film: cast vinyl tends to bend more easily around curves. Calendered vinyl is often used on flat areas or gentle curves. If your board has shaped tips, ask how the whole sheet sits on those curves.
- Glue: check if you can lift and shift the sheet before you press it down. Some films have small paths in the glue that let air out as you press. Look up removal instructions too. A film that shifts during fitting may still need heat or a special cleaner to come off later.
- Clear top layer: a laminate is a clear film that sits over the print. It helps protect the ink from scuffs. Ask if the sheet comes with one and if the maker lists it as a match for the printed film. You can also choose how shiny the finished wrap looks.
See Avery Dennison’s guide to vinyl and glue for the terms you may see on a data sheet.
Check what the cold rating means
Look for two numbers on the data sheet. The fit temperature tells you how warm it must be when you put the film on. The use range tells you what temperatures the film can take once it is on. Some sheets use the terms “application” and “service” for these two limits.
For example, one Avery Dennison film lists 10°C (50°F) as its lowest fit temperature. Its use range goes down to −45°C (−49°F). Those figures are for that film. Ask if the wrap you plan to buy has been tested on a snowboard in cold, wet use. A data sheet may list tests on a flat panel. Your board bends on each run. See the Avery Dennison film data sheet (PDF).
Size the sheet for your board
- Check the exact model and size. A wide board can have the same length as a narrow board. The Burton Custom Camber size chart shows how tip and waist widths change across sizes.
- Measure the full top of the board. Use a tape that follows the tips. Measure across the widest spot. The waist is the narrow part near the middle.
- Leave room to line up and cut. Add the trim space your wrap maker asks for on each side and at each end. Say the top is 160 cm long and 30 cm wide. Center a 170 cm by 34 cm sheet on it. You have 5 cm to spare at each end and 2 cm on each side.
- Check the mounts. If you want a sheet cut to shape, confirm the model year, size and mount type with the seller. For a sheet you cut, check the fit on your board with the backing still on. Check where the binding screws or tracks sit.
Try the look before you buy film
Pick a board shape in the studio. Add a design or upload your own art. Use the free top and 3D views to see where the art sits and what the bindings cover. Use the measurements from your board when you order the film.
Preview your snowboard wrap for freeFrequently asked questions
What is the best vinyl for a snowboard wrap?
Cast vinyl with a protective laminate is a common choice because it follows curves more easily. Check the data sheet for the fit temperature, the cold use range and removal instructions, and ask whether it suits your topsheet.
Will vinyl stick to a textured topsheet?
It depends on the glue and the texture. Give the seller your board's brand, model and year, and test a small sample before you cover the whole board.
How big a vinyl sheet do I need for a snowboard?
Measure the full length over the tips and the widest point, then add the trim margin your wrap maker asks for. A top that is 160 × 30 cm fits a 170 × 34 cm sheet with 5 cm to spare at each end and 2 cm on each side.
Is a snowboard wrap the same as a snowboard skin?
Both words are used for a vinyl film on the topsheet. Splitboard climbing skins are a different product that sticks to the base for touring.
Can I remove a vinyl wrap later?
Wrap films are made to come off, but many need gentle heat or a specific cleaner. Read the film maker's removal instructions before you buy.